Mailing List Archive

Support open source code!


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

tlug: Grrr... Why won't the same solution work for the same problem twice?



Okay, so about half a year back I was installing RH 5.1, and had a little
trouble using Xconfigurator to create my XF86config file. I came here to
TLUG, and Chris told me to make the following adjustments:

	(--) SVGA: PCI: Trident TGUI 96xx rev 211, Memory @ 0xfb800000, MMIO
@example.com
	(**) SVGA: chipset:  generic
	This is your problem.
	Remove the "chipset generic" line from your XF86Config

Cool. Then Matt recomended i use xf86config to configure my video card.
Armed with these gems of knowledge, I went to m machine and had it running
smoothly in no time.
So here it is six months later, and I'm setting up RH 5.2, and i runn into
the same problem again. "Aha!" Thinks I, "I'll just go to the TLUG archive,
get the same solution as before, and everything will be peachy".
So i go home and use xf86config to set up my XF86config file, and then I
remove the "chipset: generice" line. And my monitor goes haywire when I say
"startX". 
So after fiddling around, I discover that this time Xconfigurator has the
highest rate of success, because it won't give me a resolution higher than
320X200, but at least it doesn't turn my monitor into blithering idiot
(that's my job!)
Sigh.
So what can i try here?
_________
Included here is my XF86config file. I'm pretty sure the problem lies in
the Screen section, where, in the SVGA part, all the lines for my card have
been commented out. However, I tried uncommenting them and commenting out
mention of a "generic" video card, but that gave me near random results. 

# File generated by XConfigurator.
# **********************************************************************
# Refer to the XF86Config(4/5) man page for details about the format of 
# this file.
# **********************************************************************
# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
    RgbPath	"/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (they are concatenated together)
    FontPath	"/usr/X11R6/lib/X11/fonts/misc/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Type1/"
    FontPath	"/usr/X11R6/lib/X11/fonts/Speedo/"
    FontPath	"/usr/X11R6/lib/X11/fonts/75dpi/"
    FontPath	"/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
    # Uncomment this to cause a core dump at the spot where a signal is 
    # received.  This may leave the console in an unusable state, but may
    # provide a better stack trace in the core dump to aid in debugging
    #NoTrapSignals
    # Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
    # This allows clients to receive this key event.
    #DontZap
    # Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
    # sequences.  This allows clients to receive these key events.
    #DontZoom
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "Keyboard"
    Protocol    "Standard"
    # when using XQUEUE, comment out the above line, and uncomment the
    # following line
    #Protocol   "Xqueue"
    AutoRepeat  500 5
    # Let the server do the NumLock processing.  This should only be 
    # required when using pre-R6 clients
    #ServerNumLock
    # Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    #Xleds      1 2 3
    #To set the LeftAlt to Meta, RightAlt key to ModeShift, 
    #RightCtl key to Compose, and ScrollLock key to ModeLock:
    LeftAlt        Meta
    RightAlt        Meta
   ScrollLock      Compose
   RightCtl        Control
# To disable the XKEYBOARD extension, uncomment XkbDisable.
#    XkbDisable
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    XkbModel    "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
#    XkbModel    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    XkbLayout   "de"
# or:
#    XkbLayout   "de"
#    XkbVariant  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    XkbOptions  "ctrl:swapcaps"
# These are the default XKB settings for XFree86
#    XkbRules    "xfree86"
#    XkbModel    "pc101"
#    XkbLayout   "us"
#    XkbVariant  ""
#    XkbOptions  ""
   XkbKeycodes     "xfree86"
   XkbTypes        "default"
   XkbCompat       "default"
   XkbSymbols      "us(pc101)"
   XkbGeometry     "pc"
   XkbRules        "xfree86"
   XkbModel        "pc101"
    XkbLayout       "us"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
    Protocol    "MouseMan"
    Device      "/dev/mouse"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
#    Protocol	"Xqueue"
# Baudrate and SampleRate are only for some Logitech mice
#    BaudRate	9600
#    SampleRate	150
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
#    Emulate3Buttons
#    Emulate3Timeout    50
# ChordMiddle is an option for some 3-button Logitech mice
#    ChordMiddle
EndSection

# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
    Identifier  "MAG MX15F (1)"
    VendorName  "Unknown"
    ModelName   "Unknown"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
    HorizSync   30-65
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
    VertRefresh 50-120
# Modes can be specified in two formats.  A compact one-line format, or
# a multi-line format.
# These two are equivalent
#    ModeLine "1024x768i" 45 1024 1048 1208 1264 768 776 784 817 Interlace
#    Mode "1024x768i"
#        DotClock	45
#        HTimings	1024 1048 1208 1264
#        VTimings	768 776 784 817
#        Flags		"Interlace"
#    EndMode
# This is a set of standard mode timings. Modes that are out of monitor spec
# are automatically deleted by the server (provided the HorizSync and
# VertRefresh lines are correct), so there's no immediate need to
# delete mode timings (unless particular mode timings don't work on your
# monitor). With these modes, the best standard mode that your monitor
# and video card can support for a given resolution is automatically
# used.
# 640x400 @ 70 Hz, 31.5 kHz hsync
Modeline "640x400"     25.175 640  664  760  800   400  409  411  450
# 640x480 @ 60 Hz, 31.5 kHz hsync
Modeline "640x480"     25.175 640  664  760  800   480  491  493  525
# 800x600 @ 56 Hz, 35.15 kHz hsync
ModeLine "800x600"     36     800  824  896 1024   600  601  603  625
# 1024x768 @ 87 Hz interlaced, 35.5 kHz hsync
#Modeline "1024x768"    44.9  1024 1048 1208 1264   768  776  784  817
Interlace
# 640x480 @ 72 Hz, 36.5 kHz hsync
Modeline "640x480"     31.5   640  680  720  864   480  488  491  521
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600"     40     800  840  968 1056   600  601  605  628
+hsync +vsync
# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600"     50     800  856  976 1040   600  637  643  666
+hsync +vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768"    65    1024 1032 1176 1344   768  771  777  806
-hsync -vsync
# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768"    75    1024 1048 1184 1328   768  771  777  806
-hsync -vsync
# 1280x1024 @ 87 Hz interlaced, 51 kHz hsync
#Modeline "1280x1024"   80    1280 1296 1512 1568  1024 1025 1037 1165
Interlace
# 1024x768 @ 76 Hz, 62.5 kHz hsync
Modeline "1024x768"    85    1024 1032 1152 1360   768  784  787  823
# 1280x1024 @ 61 Hz, 64.2 kHz hsync
Modeline "1280x1024"  110    1280 1328 1512 1712  1024 1025 1028 1054
# 1280x1024 @ 74 Hz, 78.85 kHz hsync
Modeline "1280x1024"  135    1280 1312 1456 1712  1024 1027 1030 1064
# 1280x1024 @ 76 Hz, 81.13 kHz hsync
Modeline "1280x1024"  135    1280 1312 1416 1664  1024 1027 1030 1064
# Low-res Doublescan modes
# If your chipset does not support doublescan, you get a 'squashed'
# resolution like 320x400.
# 320x200 @ 70 Hz, 31.5 kHz hsync, 8:5 aspect ratio
Modeline "320x200"     12.588 320  336  384  400   200  204  205  225
Doublescan
# 320x240 @ 60 Hz, 31.5 kHz hsync, 4:3 aspect ratio
Modeline "320x240"     12.588 320  336  384  400   240  245  246  262
Doublescan
# 320x240 @ 72 Hz, 36.5 kHz hsync
Modeline "320x240"     15.750 320  336  384  400   240  244  246  262
Doublescan
# 400x300 @ 56 Hz, 35.2 kHz hsync, 4:3 aspect ratio
ModeLine "400x300"     18     400  416  448  512   300  301  602  312
Doublescan
# 400x300 @ 60 Hz, 37.8 kHz hsync
Modeline "400x300"     20     400  416  480  528   300  301  303  314
Doublescan
# 400x300 @ 72 Hz, 48.0 kHz hsync
Modeline "400x300"     25     400  424  488  520   300  319  322  333
Doublescan
# 480x300 @ 56 Hz, 35.2 kHz hsync, 8:5 aspect ratio
ModeLine "480x300"     21.656 480  496  536  616   300  301  302  312
Doublescan
# 480x300 @ 60 Hz, 37.8 kHz hsync
Modeline "480x300"     23.890 480  496  576  632   300  301  303  314
Doublescan
# 480x300 @ 63 Hz, 39.6 kHz hsync
Modeline "480x300"     25     480  496  576  632   300  301  303  314
Doublescan
# 480x300 @ 72 Hz, 48.0 kHz hsync
Modeline "480x300"     29.952 480  504  584  624   300  319  322  333
Doublescan
EndSection

# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
Section "Device"
    Identifier        "Generic VGA"
    VendorName        "Unknown"
    BoardName "Unknown"
    Chipset   "generic"
#    VideoRam 256
#    Clocks   25.2 28.3
EndSection
# Device configured by Xconfigurator:
Section "Device"
    Identifier  "TG 9660 / Cyber9385"
    VendorName  "Unknown"
    BoardName   "Unknown"
    #VideoRam    1024
    # Insert Clocks lines here if appropriate
EndSection

# **********************************************************************
# Screen sections
# **********************************************************************
# The Colour SVGA server
Section "Screen"
    Driver      "svga"
    Device      "Generic VGA"
    #Device      "TG 9660 / Cyber9385"
    Monitor     "MAG MX15F (1)"
    Subsection "Display"
        Depth       8
        #Modes       "1024x768"
        ViewPort    0 0
        Virtual     320 200
        #Virtual     1024 768
    EndSubsection
EndSection
# The 16-color VGA server
Section "Screen"
    Driver      "vga16"
    Device      "Generic VGA"
    Monitor     "MAG MX15F (1)"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection
# The Mono server
Section "Screen"
    Driver      "vga2"
    Device      "Generic VGA"
    Monitor     "MAG MX15F (1)"
    Subsection "Display"
        Modes       "640x480" "800x600"
        ViewPort    0 0
        Virtual     800 600
    EndSubsection
EndSection
# The accelerated servers (S3, Mach32, Mach8, 8514, P9000, AGX, W32, Mach64
# I128, and S3V)
Section "Screen"
    Driver      "accel"
    Device      "TG 9660 / Cyber9385"
    Monitor     "MAG MX15F (1)"
    Subsection "Display"
        Depth       8
        Modes       "1024x768"
        ViewPort    0 0
        Virtual     1024 768
    EndSubsection
EndSection




-------------------------------------------------------------------
Next Technical Meeting: February 13 (Sat), 12:30 place: Temple Univ.
** presentation: XEmacs, by Steven Baur and Martin Buchholz
Next Nomikai: March 19 (Fri), 19:30   Tengu TokyoEkiMae 03-3275-3691
-------------------------------------------------------------------
more info: http://tlug.linux.or.jp                     Sponsor: PHT


Home | Main Index | Thread Index

Home Page Mailing List Linux and Japan TLUG Members Links