tlug: Re:MO & SCSI Logitec LMO-640E / Fujitsu + Mouse Problem

[Yuval <yuval@example.com>]

Hi Again,

>I am trying to get my Linux 2.0.0 / 2.0.34 versions to
>read the following MO/SCSI combination.
>Logitec LMO-640E / Fujitsu M2513EL (MO - Magento Optical Disk )
>SYMBIOS 53C8XX  ID7
>
>

Question 1:

I used these options in make config:

NCR53C8XX SCSI support
(CONFIG_SCSI_NCR53C8XX) [Y/m/n/?]
 detect and read serial NVRAMs (CONFIG_SCSI_NCR53C8XX_NVRAM_DETECT) [Y/n/?]

  enable tagged command queueing (CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE)
[Y/n/?]
  use normal IO
(CONFIG_SCSI_NCR53C8XX_IOMAPPED) [Y/n/?]
  maximum number of queued commands
(CONFIG_SCSI_NCR53C8XX_MAX_TAGS) [4]
synchronous transfers frequency in MHz
(CONFIG_SCSI_NCR53C8XX_SYNC) [5]
 assume boards are SYMBIOS compatible
(CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT) [Y/n/?]

------------------------------------------------
At boot time, this is the message I get :
(The serial driver information is for Question #2)

kernel:
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
 tty01 at 0x02f8 (irq = 3) is a 16550A
lp1 at 0x0378, (polling)
PS/2 auxiliary pointing device detected -- driver installed.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
ncr53c8xx: at PCI bus 0, device 13, function 0
ncr53c8xx: 53c875 detected with Symbios NVRAM
ncr53c875-0: rev=0x03, base=0xfffbff00, io_port=0xfc00, irq=9
ncr53c875-0: Symbios format NVRAM, ID 7, Fast-20, Parity Checking
ncr53c875-0: on-board RAM at 0xfffbe000
ncr53c875-0: restart (scsi reset). kernel: ncr53c875-0-<5,0>:
FAST-10 SCSI 10.0 MB/s (100 ns, offset 15)
 ------------------------------------------------------
However I could not find an assigned device name ,,so I tried
to mount /dev/sda1 :
mount -t vfat /dev/sda1 /mo

I get:
mount: /dev/sda1 is not a valid block device
 ------------------------------------------------------
Quesiton 2:
In addition, when I start the X11 window manager (startx), the mouse is
frozen.  Using 2.0.0, I get the same messages in the boot stage
but the mouse is not frozen.
Any clues ?

These are the make config settings
(My mouse is a three button PS/2 type (psaux) according to my working
2.0.0)
 *
* Character devices
*
Standard/generic serial support (CONFIG_SERIAL) [Y/m/n/?]
Digiboard PC/Xx Support (CONFIG_DIGI) [N/y/?]
Cyclades async mux support (CONFIG_CYCLADES) [N/y/m/?]
Stallion multiport serial support (CONFIG_STALDRV) [N/y/?]
SDL RISCom/8 card support (CONFIG_RISCOM8) [N/y/m/?]
Parallel printer support (CONFIG_PRINTER) [Y/m/n/?]
Specialix IO8+ card support (CONFIG_SPECIALIX) [N/y/m/?]
Mouse Support (not serial mice) (CONFIG_MOUSE) [Y/n/?]
ATIXL busmouse support (CONFIG_ATIXL_BUSMOUSE) [Y/m/n/?]
Logitech busmouse support (CONFIG_BUSMOUSE) [Y/m/n/?]
Microsoft busmouse support (CONFIG_MS_BUSMOUSE) [Y/m/n/?]
PS/2 mouse (aka "auxiliary device") support (CONFIG_PSMOUSE) [Y/m/n/?]
C&T 82C710 mouse port support (as on TI Travelmate) (CONFIG_82C710_MOUSE)
[Y/n/?]

> --------------------------------------------------------------
> Next Meeting: 8 August, Tokyo Station Yaesu central gate 12:30
> featuring Linux on multiple platforms:
> i386, Sparc, PA-Risc, Amiga, SGI, Alpha, PalmPilot, ...
> Next Nomikai: 18 September, 19:30 Tengu TokyoEkiMae 03-3275-3691
> --------------------------------------------------------------
> Sponsor: PHT, makers of TurboLinux http://www.pht.co.jp



--------------------------------------------------------------
Next Meeting: 8 August, Tokyo Station Yaesu central gate 12:30
featuring Linux on multiple platforms:
i386, Sparc, PA-Risc, Amiga, SGI, Alpha, PalmPilot, ...
Next Nomikai: 18 September, 19:30 Tengu TokyoEkiMae 03-3275-3691
--------------------------------------------------------------
Sponsor: PHT, makers of TurboLinux http://www.pht.co.jp