Mailing List Archive

Support open source code!


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

nic config [was: [tlug] RH7.2 - no linuxconf?]



sajjid,

just read your message about bringing a network interface card up and
running. i am currently experiencing the same problem (i.e. kernel doesn't
detect the card). my question: does your answer only apply to the case when
the driver is compiled as a module? or do i have to take these steps also
when i compiled the driver into the kernel?

-mario

----- Original Message -----
From: "A.Sajjad Zaidi" <sajjad@example.com>
To: <tlug@example.com>
Sent: Tuesday, March 05, 2002 14:24
Subject: Re: [tlug] RH7.2 - no linuxconf?


> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hi Scott,
>
> linuxconfig has always been a pain for me and never got things right.
>
> Try using '/usr/sbin/netconfig'. Its simpler and meant for getting your
> network up quickly.
>
> Before that, your problem seems to be with the kernel not recognizing
> your network card. The file /etc/modules.conf should have an entry like
> 'alias eth0 eepro100', based on your NIC (Intel Ethernet Pro 100 in this
> case).
>
> After adding that, run '/sbin/depmod -a' and then 'modprobe eepro100'
> (replacing eepro100 with the module for your card). Then use netconfig
> to setup networking.
>
> That should be it. Let us know your progress.
>
> - --
> A. Sajjad Zaidi
> System Administrator
> Technology & Operations Div.
> Digital Garage Inc.
>
>
> On Tue, Mar 05, 2002 at 09:24:00PM +0900, scott in sendai wrote:
> > Hi TLUG,
> >
> > A little problem here. Up until yesterday I was running
> > mandrake 8.1 on a cable modem, and had sucessfully set up
> > IPmasq for 2 other wkstns to do NAT, everything fine.
> > Mandrake would configure things without allowing me to
> > change or see what it was doing so I decided to write down
> > all my NIC and IP settings and install RH7.2 instead.
> > However, RH7.2 doesn't have linuxconf, only NEAT, which
> > fails to recognize my NIC despite trying many possible
> > combinations. RH7.2 also failed to recognize the NIC
> > during bootup (no ETH0 initialization- it doesn't even say
> > [FAILED]. Ifconfig of course only shows the lo, and no
> > eth0. I took out the other NIC for the internal lan and
> > reinsalled, but no change.
> >
> > Anyone using 7.2? If so any ideas on how to install
> > linuxconf? I tried using the RPM manager but it doesn't
> > show up. Should I just go back to mandrake?
> >
> >    TIA,
> >
> >    Scott VanDusen
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Yahoo! BB is Broadband by Yahoo!  http://bb.yahoo.co.jp/
> >
>
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.0.6 (GNU/Linux)
> Comment: For info see http://www.gnupg.org
>
> iD8DBQE8hMcNt1KjqyZ+DQ4RAtjTAJ9rgAusAMz7c2DOW9U6V+gNA7W6vgCgvtRX
> CvSXKIBjD7Xbqa5iGh1DZIo=
> =6TDG
> -----END PGP SIGNATURE-----


Home | Main Index | Thread Index

Home Page Mailing List Linux and Japan TLUG Members Links